Series 46H-413 | Hi-Build Tneme-Tar

Generic Type Polyamide Epoxy-Coal Tar
Common Usage High-build corrosion resistant coating providing one coat protection for concrete and steel in a variety of chemical, immersion and underground conditions. Also, when a two-coat application is desired, a low film build option is possible.
Colors Black
Finish Semi-gloss
Primers Steel: Self-priming or Series 1, 66, N69, N69F, 90-97, H90-97, 161
Galvanized Steel: Series 66, N69, N69F, 161
Concrete: Self-priming, 63-1500, 218
Volume Solids 75.0 ± 2.0% (mixed)
Recommended DFT 16.0 to 20.0 mils (405 to 510 microns)
8.0 to 10.0 mils (200 to 250 microns) for the two-coat option
Curing Time
Temperature To Touch To Recoat (Min./Max) Immersion
95°F (35°C) 2 hours 3-14 hours 5 days
85°F (29°C) 3 hours 4-18 hours 6 days
75°F (24°C) 4 hours 6-28 hours 7 days
65°F (18°C) 6 hours 10-50 hours 10 days
55°F (13°C) 9 hours 16 hrs-3 days 14-16 days
45°F (7°C) 18 hours 32 hrs-4 days 22-24 days
35°F (2°C) 26 hours 44 hrs-6 days 28-32 days

Curing time varies with surface temperature, air movement, humidity and film thickness.
Use the above times as guidelines only. Scarify the surface with fine abrasive before recoating if the maximum recoat time has been exceeded.
Volatile Organic Compounds Unthinned: 1.91 lbs/gallon (229 grams/litre)
Thinned 20% (No. 2 Thinner): 2.80 lbs/gallon (335 grams/litre)
Thinned 20% (No. 65 Thinner): 1.91 lbs/gallon (229 grams/litre)
Theoretical Coverage 1,203 mil sq ft/gal (29.5 m²/L at 25 microns). See APPLICATION for coverage rates.
Number of Components Two: Part A and Part B

The products listed below are not exact equivalents. They are only products that you may consider as alternatives in a general sense. Substrate type, condition, temperatures, surface preparation, primer/topcoat selection and intended use are just a few factors that will affect product selection. Please contact your local Tnemec Coatings Consultant for product recommendations.

This ProductPolyamide Epoxy-Coal Tar
Volume SolidsRec. DFTV.O.C.# of Components
75.0 ± 2.0% (mixed)16.0 to 20.0 mils (405 to 510 microns)
8.0 to 10.0 mils (200 to 250 microns) for the two-coat option		Unthinned: 1.91 lbs/gallon (229 grams/litre)
Thinned 20% (No. 2 Thinner): 2.80 lbs/gallon (335 grams/litre)
Thinned 20% (No. 65 Thinner): 1.91 lbs/gallon (229 grams/litre)		Two: Part A and Part B
Series 46-465 | H.B. Tnemecol Coal Tar
Hide this product's data
Volume SolidsRec. DFTV.O.C.# of Components
64.0 ± 2.0%8.0 to 12.0 mils (205 to 305 microns) per coat. Note: Number of coats and thickness requirements will vary with substrate, application method and exposure. Contact your Tnemec representative.Unthinned: 2.56 lbs/gallon (306 grams/litre)
Thinned 5%: 2.78 lbs/gallon (333 grams/litre)		One

Email this product